FAQ
ZULUS HD
1. "What battery does the ZULUS use?"
You can use flat-top 18650 batteries with specific dimensions of 65mm*18mm (Note: Some 18650 batteries in certain areas may come with a protection board, increasing the length to 68mm~69mm. These longer batteries cannot be used inside the device).
2. “What's the device's Wi-Fi password?”
DNT device uses a fixed WPA2 password: 12345678
3. "What is the warranty for the ZULUS scopes? "
ZULUS scopes have a 2 year warranty.
4. "Is the IR Fixed or Adjustable?"
The IR light is fully adjustable allowing you to have a wide flood for closer range or a tight spot for further distances.
5. "What is the eye relief"
45mm
6. "Can I use the ZULUS during the Day and Night?”
Yes, the Zulus is a digital scope that will show full color for day use and monochrome for night use.
7. "Is the optic waterproof?”
Yes it is IP67 waterproof.
8. "What is the recoil rating?
.50 BMG rated
9. "Do I need a light to see in night mode?"
That depends on the amount of ambient light like dusk or dawn. But for truly dark nights the ZULUS has a built-in infrared illuminator to help you see in the dark.
10. "Can the scope record sound or is it just video?"
Yes, the scope has the option to turn on and off a built in microphone adding sound to the video you are recording.
11. "Why does the IR illuminator automatically dim or turn off?"
This is to prevent the IR illuminator from overheating. When IR illuminator brightness is set to level 4 or 5 it can generate a lot of heat. In order to protect the ZULUS the illuminator will automatically drop to level 3 after 10 minutes of use. All brightness levels will automatically turn off after 30 minutes of continuous use.
12. "How many zeroing profiles can I have?"
26 in total A-Z
13. "How do you get the zulus into night mode?"
To get into night mode you long press the left arrow while the screen is in normal operating mode NOT in the menu.
14. "How do you change the reticle and the reticle color?"
Changing the reticle and the color is done in the zeroing menu.
15. "How do you save your zeroing profile?"
Long press the left arrow to save and exit.
16. "How do you change the IR brightness?"
When you are in night mode, short press the left arrow. This will allow you to change the IR illuminator brightness. There are 5 brightness levels and an auto brightness mode.
17. "How do you freeze the screen while zeroing?"
When in the zeroing menu short press the power button to freeze the image.
18. "How do you turn wifi on?"
There are 2 ways the first is long press the right arrow this will activate the wifi. The second way is to go into the settings menu amd scroll to wifi and turn on.
19. "How do you turn on Bluetooth?"
Go into the settings menu and scroll to the Bluetooth option press the up arrow to enter and turn on.
20. "What does RAV mean?"
Recoil Activated Video. If the recoil impulse is high enough the ZULUS will record what it sees a couple seconds before and after a shot is taken. That way in case you forgot to press record manually, you can still get a video recording of your shot.
21. "Minimum recoil needed to active RAV"
Approximately 450G of force. For example a 5.56/.223 Remington can activate the RAV but not a .22lr or most airguns.
22. "How do you get the ZULUS in standby mode?"
In normal operating mode, short press the power to enter standby mode. You will know you have entered standby mode when the top light turns orange and the screen is off.
ZULUS HD V2
1. "What type of battery does the ZULUS V2 use?"
It uses a flat-top 21700 battery.
2. “What is the screen size of the ZULUS V2?”
It has a 0.49-inch display.
3. "How many reticle options are available on the ZULUS V2?"
The ZULUS V2 offers 9 built-in reticle options: 2 FFP and 7 SFP reticle types.
4. "Can I access the menu while Wi-Fi is on?"
Yes. With the new UI design, you can access the menu while Wi-Fi is enabled.
5. "Are the IR illuminators of the ZULUS V1 and V2 interchangeable?"
No. The ZULUS V2 uses an M24-sized IR illuminator, while the V1 uses M21. They are not interchangeable.
6. "Can I change the color of the reticle on the ZULUS V2?”
Yes, by short-pressing the Menu button, you can select from five reticle colors: red, green, yellow, black, and white.
7. "Why doesn’t the ZULUS V2 have Bluetooth? How do I upload ballistic data?”
The ZULUS V2 features a built-in ballistic calculator. You can enter the data on your phone and sync it via Wi-Fi, or make adjustments directly on the device.
8. "What’s different about the magnification system on the ZULUS V2 compared to the V1?”
The ZULUS V2 features both a magnification wheel and a lever, providing smoother and more ergonomic magnification control compared to the V1.
9. "What upgrades were made to the ocular on the ZULUS V2?”
The ocular lens diameter has been increased to 41mm, and eye relief has been extended to 65mm.
10. "Has the rangefinder been improved in the ZULUS V2?”
Yes. The V2 supports a range of 5–1000 meters and adds three modes: Continuous Ranging, Single Pulse Ranging, and Timed Ranging (3s, 5s, or 10s).
ThermNight TNC
1. "What type of battery should I use?"
You can use flat-top 18650 batteries with specific dimensions of 65mm*18mm for ThermNight - TNC225R. And use flat-top 21700 batteries with specific dimensions of 70mm*21mm for ThermNight - TNC335R & ThermNight - TNC635R (Note: Some 18650/21700 batteries in certain areas may come with a protection board, the length will increase by 3mm-4mm. These longer batteries cannot be used inside the device).
2. "What is the warranty for the ThermNight TNC?”
ThermNight TNC225R have a 2 year warranty. TNC335R & TNC635R have a 3 year warranty.
3. "What should I do if the scope display screen turns red or blue?"
More often than not, the problem is usually caused by poor contact of the battery cap.
Ensure that the battery cap is securely tightened.
Clean the internal threads of the battery cap to make sure there’s no dirt or any other debris that could block the circuit contact.
4. "Why does the IR illuminator automatically dims or turns off?"
This is to prevent the IR illuminator from overheating. When IR illuminator brightness is set to level 4 or 5 it can generate a lot of heat. In order to protect the ThermNight the illuminator will automatically drop to level 3 after 10 minutes of use. All brightness
levels will automatically turn off after 30 minutes.
And for the LED type illuminator, the maximum brightness level is only 3. It will not dim automatically, but it will automatically turn off after 30 minutes of continuous use.
5. "Recoil rating?”
.50 BMG
6. "Do I need to purchase a new memory card for ThermNight TNC?"
No, the ThermNight -TNC225R comes with a built-in 32GB memory card. The ThermNight -TNC335R & ThermNight -TNC635R comes with a built-in 64GB memory card.
7. "How do I measure the scope height of ThermNight TNC?"
Measure the distance from the center of the top digital scope lens to the center of the barrel.
8. "Will strong sunshine damage the thermal sensor?"
Yes, do not aim the thermal scope at strong heat sources such as the sun or fire, as this can damage the thermal sensor permanently.
9. "For ThermNight TNC, why are the reticles of thermal and night vision are not aligned?"
It’s normal. After zeroing at a specific distance, the reticles align at that distance, and when the aimed object is off the zeroing distance, the reticles do not align at same reference (it doesn’t affect the holdover/dial in calculation result)
10."How do I zero the ThermNight TNC?"
There’re several steps to get both night vision and thermal channel zeroed.
1. One-shot zero the night vision channel,
2. There’s no need to shoot for the zeroing of thermal channel. After your night vision channel is zeroed, switch to thermal mode, and use the same heat spot as a reference(such as a hot bottle of water).
Shift the thermal reticle to the same reference area, make sure the thermal reticle is aligned with night vision reticle, and save it.
Note: Both night vision and thermal channel need to be zeroed for accurate target shooting.
Hydra
1. "What battery does Hydra use?"
You can use flat-top 18650 batteries with specific dimensions of 65mm × 18mm (Note: Some 18650 batteries in certain areas may come with a protection board, increasing the length to 68mm–69mm. These longer batteries cannot be used inside the device).
2. "Do I need to purchase a new memory card for Hydra?”
No, Hydra comes with 32GB of built-in storage.
3. "Will strong sunshine damage the thermal sensor?"
Yes, do not aim the thermal scope at intense heat sources, such as the sun or fire, as this can permanently damage the thermal sensor.
4. "What is the warranty for the Hydra scopes?"
HS225 & HS325 have a 2-year warranty, and HS635 has a 3-year warranty.
5. "What's the device's Wi-Fi password?”
All DNT devices use a fixed WPA2 password: 12345678
6. "What types of optics can Hydra be used with as a clip-on?"
The Hydra is compatible with LPVO (*For optimal performance, we recommend using the lower half of your LPVO's magnification range.) and low magnification prism optics.
7. "What is the recoil rating of Hydra?"
Its recoil resistance is up to .50 BMG / 800 Gs.
8. "Can I use a USB-C battery bank for extended life of Hydra?"
Yes, Hydra supports an external power supply to extend battery life while in use, but please note: the external power supply cannot charge the 18650 battery in the machine. If you want to charge the battery, please take it out and use the battery charger to charge it.
9. "Can the Hydra clip-on be used with a red dot sight?"
No. However, some users have reported limited success depending on the red dot models used. DNT Optics is currently field-testing this configuration, but as of today, we do not officially support it. Alternatively, if your red dot uses a QD mount, you can use Hydra as a stand-alone optic.
10. "Do any of the Hydra models have an integrated laser rangefinder (LRF)? "
The current Hydra thermal scopes does not include an LRF so there is no ballistics calculator offered in the device.
11. "Does Hydra come with a mount? "
Yes, Hydra comes with DNT's PMS mount found on other Digital DNT optics and is footprint-compatible with the QD mount.
12. "Can I zoom in the clip-on mode? "
No. While in clip-on mode, you are not zooming the Hydra’s digital image; you increase the zoom of your LPVO or flip up your magnifier if you are using that combo.
13. "How to Zero Hydra? "
Please follow the steps below:
Step1: Aim at the target at your preferred zeroing distance (we recommend 50 yards for Hydra). Adjust the objective lens so the target is in focus. Fire one round at target, and the bullet will impact on or near the target.
Step 2: Keep your Hydra steady and the reticle aimed at your original Point of Aim (POA). Short press the Power Button to freeze the current image.
Step 3: Adjust the X and Y positions of the reticle to move the POA to your Point of Impact (POI).
Short press the Menu button to select either X or Y, then use the Zoom button to move the reticle up/down and the Record button to move it left/right until it aligns with the POI.
Step 4: Move the cursor to "Save" and short press Menu Button to save and exit.
Note: If you use Hydra as a clip-on, you need to turn on the clip-on mode before zeroing.
14. "Do I need to re-zero Hydra after removing it and reinstalling it?"
No. As long as your QD mount doesn't lose tension on the base and you reindex the mount to the same position, you can remount it onto the same rifle without needing to re-zero.
However, since Hydra does not have ballistics built into the unit, you will have to zero the optic if you mount it to a different rifle.
DNT App
1. "I know very little about ballistics. Is the app accurate?"
You don't need to understand complex terms or have extensive knowledge of ballistics. Simply measure and input ballistic parameters accurately to get the ballistic solution. The ballistic algorithm has been tested through live shooting and theoretical analysis, ensuring sufficient accuracy to meet the requirements of different hunting scenarios.
2. "Must the app always be connected during usage?"
Only if you are using the In real-time calculation mode, a continuous connection is required if not the ballistic calculations cannot be performed. The other option is ballistic table call mode which allows the ballistic data to be uploaded to the device and no phone is needed after the upload is completed.
3. "Why does the rangefinder display measurement errors?"
There are several reasons for the ranging error.
1. The target is out of range. Our built-in LRF can range from 5 yards to 1100 yards.
2. The target might not be reflective enough for the laser range finder pulse to bounce back and be measured.
3. Weather can affect the LRF performance such as fog or heavy rain.
4. Something might be blocking the LRF, check to make sure the aperture is clear.
5. Possible hardware issue. Please contact us with any problems.
4. "Why does the rangefinder box or spot move out of the frame when zoomed in?"
The LRF is fixed at the factory so if you zoom in the LRF aiming reticle may be outside your current FOV. Scroll back and reduce magnification to see LRF reticle.
5. "Does the 20MOA rail or a 35MOA mount change the way the ballistic data works"
The angle of the rail or mount does not affect the calculation results. As long as you input the correct scope height by measuring center of lens to center of the barrel (**BORE?), zero distance, actual parameters. normal input of accurate scope parameters is sufficient.
6. "How do I measure my 'Scope Height'?"
Take a pair a calipers or a ruler and measure from the center of your barrel or bolt.firing pin to center of the scope lens. Make sure you measure straight and not at an angle. For the ThermNight measure from the digital Day/NV objective lens, not the thermal lens.
7. "I changed some parameters, but the calculation results did not change."
Two things to watch out for.
First after you have changed the parameters make sure you long press left arrow to save; otherwise, the data changes will not take effect.
The second thing is made sure the changes you made were done on the correct profile letter A-Z.
8. "Why does the ballistic table indicate wind deflection even though wind speed is not set?"
The ballistic algorithm includes calculating wind spin drift.
9. "I am getting an error saying ‘out of range’. "
If the ranging distance exceeds the farthest distance set in the ballistic table (end distance), it will prompt "out of range." Resolve this by setting the farthest distance beyond commonly used shooting records. Also, consider setting a smaller step value (incremental distance) for finer calculation results.
10. "Why can't I see the rangefinder box or spot when zoomed in? "
Your zero is now too far away from the fixed LRF aim point. Simply reduce the magnification until the rangefinder box or spot appears on the screen for measurement before you zoom in.
11. "What does aiming method mean?"
Aiming method is used when you have enabled the ballistic calculator. With the proper ballistics entered into the app, your digital scope will show you where to aim for the ballistic drop at that distance. Hold over will show you a hash mark relative to your zeroed reticle. The Dial-In option will move the reticle to the ranged position. Clear the laser range finder measurement by pressing and holding down the LRF button and the reticle will move back to its zeroed position.
12. " What ballistic calculation option is recommended."
Ballistic table call will allow you to send one ballistic profile to the scope so you don't have to stay connected to the phone.
13. "Google Play cannot install The DNT Optics app."
Google Play may not support some phones, preventing the download through the Google Play Store . Email us at info@dntoptics.com to request the latest installation package.
14. "Why can't I successfully connect to the app?"
Ensure that the app has the necessary permissions for Bluetooth, WiFi, and local file access. It is essential to enable GPS location during app usage; otherwise, normal app operation and connection may be affected. Consider clearing the cache or reinstalling the app to resolve connection issues.
15. "How to avoid disconnection issues during app connection?"
Bluetooth and WiFi have limited transmission distances, and increased distances may lead to disconnection or delays in connection. It is advisable to maintain a close distance and minimize obstructions.
- Choosing a selection results in a full page refresh.